• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

Allowing your cat to enter and go from the house at their own pace is a great idea to keep it physically and mentally active. A flap can reduce accidents with toilets by making it easier for cats to leave the home when required.

Measure the Door

A cat flap lets your pet leave and come back whenever they want without you having to open the door. This makes it ideal for keeping them in when you're home or away and helps to keep unwanted pests from the house as well!

It is important to measure the door to ensure that you have the correct size cat flap. There are many sizes available. You can then ensure that the cat flap is the correct size for your upvc doors. Otherwise, it may be too big or small, and your cat could be unable to use it.

Use a ruler to determine the width at several points along the edge of the door. You should also measure the door's height in a few places. This is because the door that is too high could cause your cat to perform a gymnast's routine every time they want to use the flap!

Get help from a glazier if you aren't sure how to measure the door. They should be able to assist you in determining whether or not your door is suitable for a cat flap, and help you decide on the best size of flap you should purchase.

Draw the shape of your hole on the door once you have the measurements. This will provide you with an idea of how to cutting the hole and will prevent you from making an error that will cost you money in the end!

You must also ensure that the hole you're making is in the correct place. For instance, if installing the cat flap on a patio door, it is important that the hole is not too close to any hinges, since this could cause leakage and problems with the seal.

It is best to leave the task of installing the cat flap on glass doors to an experienced glazier. It can be difficult to install a cat flap installation bristol flap into the glass pane and you could be surprised to find that the process causes it to break and lose its weatherproof seal.

Measure the Cat

A cat flap permits your pet to go and come whenever they want without having to leave them home to themselves. It can also prevent draughts entering your home, which isn't good for your cat as well as you.

If you do have a uPVC or composite door it can seem tricky to fit the cat flap. These kinds of doors are usually constructed of different materials than standard wooden or uPVC doors and the procedure for installing them is quite different too. Before you decide to install an egress flap to your uPVC or composite door, make sure that it is compatible and that you have consulted the manufacturer as any modifications could invalidate any warranties.

These doors are generally designed to be durable and tough, with insulation. This makes them more resistant to weather elements than other doors, however they can be difficult to fit the cat flap. Make sure to consult a professional prior to installing a cat flap onto the uPVC door or composite.

You'll need to take their height to ensure they pass through the door. This is easiest if they are asleep or calm so that they don't move around too often. Once you know their height, measure the distance between their stomachs and the floor to determine where the bottom of the cat flap installer flap needs to go. This location can be outlined on the door.

If you are using power tools to cut your uPVC door or composite door, you need to be careful. Drilling into metal can cause cracks, especially if the area is composed of toughened glass. This is the reason it's advisable to hire a glazier when installing your cat flap inside a pane of glass. This will stop the glass from breaking or becoming brittle. Glaziers can also provide you with a circular hole to use for the cat flap, which will be less likely to break and is safer for your cat to use.

Cut the Hole

A good quality cat flap should come with a template that can be used to mark the spot on your door where the hole needs to go. If it does not then you can make one using an uncoated sheet of paper (tracing paper is the best choice). Once the shape has been pencilled in on the door, you can then use a spirit level to make sure that the shape is horizontal. This will ensure that your cat flap is positioned correctly in the opening, and it won't slide open or close.

Next, take your jigsaw, and cut the shape drawn on the door. Use a blade designed specifically for uPVC doors. It will typically be identified with this information. If not then ask the staff at your DIY store for assistance. After the hole has been cut then place the flap against it and open it to ensure that the flap moves smoothly. If it becomes stuck at any point, you can use the filer or the rasp to correct this.

It is also important to ensure that there are no electric gas or cable lines within the door you will be cutting through, because they could be damaged by the jigsaw. Additionally, you should be aware of any handles or other fixtures on the door that need to be removed in order to make room for the cat flap. Be careful not to damage them during the process.

Most people who install a cat flaps flap on their own have the standard solid uPVC front door, which means they won't be faced with these issues. If your door is constructed of wood or has a decorative element that isn't easily removed, this can make the job.

It is always worthwhile seeking professional assistance from a cat flap fitter for these kind of jobs as it is essential to do them done right to avoid possible issues in the future. Making the wrong choice could cause the door to be damaged and could make it impossible to honor the warranty.

Install the Flap

Once you have cut your hole, put the flap and check if it opens and fits. If you notice any spots that stick or catch, file them down with an sandpaper or hand file until it fits correctly and opens without issue. Make sure the flap is flush with the door.

If your kit doesn't have an example, you could use tracing paper that is thin, such as a piece of paper or Acetate. Place the paper on the door and draw an area on which you'll want to position the flap (this will be your cutting guide). Then, using the pencil lines you've drawn on the door, mark four screw holes in each corner of the flap. These are the screw holes you'll use to put it in the right position.

Most uPVC doors are solid and therefore easy to cut into. If your door is constructed of GRP or composite however, it could be more difficult. If you're not comfortable with this, it is recommended to consult a professional. They can also tell you if your door is suitable for the installation of the cat flap.

If you are planning to install a cat flap into composite doors, you need to first check with the manufacturer or a professional joiner. Any alterations made to these doors could make it impossible to honor the warranty. If you decide to carry out the work yourself, remember that this could be messy and possibly dangerous task.

You'll need to use a saw or grinder to cut through composite doors, rather than just the GRP. Be aware that this can be very dangerous and you'll need to take great care not to hurt the door or yourself, as it is extremely fragile. It's important to remember that it's much more difficult to make a hole in fitting a cat flap in a upvc door (Highly recommended Internet site) door glass than in a uPVC door or solid wood door.